Polar Force branding illustration

A CANADIAN BRAND · POLAR FINISHING EQUIPMENT

POLAR FORCE.

Heavy-duty metal sanding

Explore belt and brush configurations for your surface preparation and finishing requirements.

Catalogue exterior with Polar branding digitally applied. Example configuration.

A clear path to selection

Your parts. Your process. Your finish.

01 · Define the work

Identify material, dimensions, incoming condition and the surfaces to be processed.

02 · Review the result

Agree on appearance and inspection requirements before evaluating representative samples.

03 · Confirm the scope

Document the selected machine, tooling, extraction, site requirements and commissioning responsibilities in the offer.

The Polar family

Explore the complete range.

Build your quotation

Confirm the configuration.

Parts and process

Send material grade, width, thickness, length, flatness and incoming surface condition. Identify the faces to process and any protective film.

Finish and acceptance

Provide a reference finish and representative parts. Agree on grain direction, appearance, measurement method and acceptable marking before ordering.

Equipment and site

Confirm working width, head arrangement, abrasives, feed range, electrical supply, extraction and any wet-processing system. Document guarding, local electrical approval, installation and training scope.

Specifications, accessory inclusion, pricing and delivery are confirmed in the written offer. Processing results depend on the selected configuration, material, abrasives and incoming part condition.

Documented configuration

Polar Force — 900 mm reference.

The following values describe the 900 mm configuration in the supplied metal-sander technical sheet. They are not universal limits for every Force model; gallery photographs include other example arrangements.

On smaller screens, swipe the table to see all columns.

Technical itemCatalogue referenceSelection note
Working width900 mmFor the documented configuration.
Working thickness1–120 mmSheet-listed range; confirm part size, flatness and holding requirements.
Abrasive belt width915 mmFor the belt stations in this reference.
Abrasive belt length75 inConfirm replacement-belt dimensions for the ordered configuration.
Feed controlServo-controlled; 1–20 m/minFeed setting is not a guaranteed production rate.
Feed motor3 HPReference-sheet rating.
Table movement motor0.5 HPPowered working-thickness adjustment.
Table height970 mmConfirm the final installation drawing.
Head sequenceBelt / disc / belt illustratedSelect the actual tooling and station arrangement.
Head motor ratingsConfirm with quotationConfirm the rating of each drive for the selected head arrangement.
Vacuum workholdingConfirm inclusionSpecify vacuum workholding and its inclusion in the written quotation.
Belt-cleaning air jetsOptional in the technical sheetConfirm compressed-air requirements and inclusion.
Original catalogue photography

Outside and inside the sanding process.

Interior photographs show example metal-sander arrangements. Head count, drive layout and brush equipment vary by configuration.

Machine construction

Controls, handling and service access.

Tracking and belt changes

The metal-sander catalogue lists conveyor tracking, a quick-release sanding-belt mechanism and a main-motor load meter. The Force technical sheet also describes abrasive-belt oscillation and tensioning.

Table and part support

Four-point table support, powered thickness adjustment and infeed/outfeed support are documented on the referenced configurations. Confirm minimum part size, support length and vacuum holding separately.

Controls and protective devices

The Force reference describes a front touch screen, motor overload protection, emergency stops and shutdown conditions for belt or air-supply faults. Site electrical approval and the final guarding package must be confirmed for the supplied machine.

The sanding process

Top, bottom and combination heads.

Catalogue diagrams of top sanding A-A and A-A-A heads and bottom sanding A and A-A heads

Choose the face and the sequence.

The metal-sander catalogue illustrates top sanding with two or three roller heads and bottom sanding with one or two roller heads. These are alternative machine arrangements; a top-sanding machine does not automatically include bottom sanding.

A roller head uses an abrasive belt over a contact roller. Brush or disc stages are selected separately around edge treatment, surface appearance and part geometry. For two-face work, confirm whether the proposed process uses separate machines, a dedicated line or part reversal.

Discuss your head configuration ↗
Tooling choices

Match the brush to the finish.

Original catalogue tooling photographs. These are selection options, not a statement that every brush is included or fits every Polar model.

Abrasive-cloth brush

Abrasive-cloth brush

Abrasive flaps with supporting fibres. Specify the abrasive, grit and required surface treatment.

Disc brush

Disc brush

A disc-format tool for a compatible brushing station. Confirm part holding and the desired edge result.

Nylon brush

Nylon brush

A catalogue-listed brush format. Confirm filament type and compatibility with the work material.

Wire brush

Wire brush

Select wire type and material compatibility; agree on acceptable marking and contamination controls.

Non-woven brush

Non-woven brush

A non-woven abrasive format for evaluating blending and finishing requirements.

Fibre brush

Fibre brush

A fibre-bristle format. Confirm its cleaning or finishing role in the selected machine.

Start with your parts

Let’s define your finish.

Bring your material, part dimensions, incoming condition and target finish. We’ll use those details to discuss the machine and quotation scope.

Discuss your application ↗
RISE TEK · POLAR FINISHING EQUIPMENT

Get your Polar quotation.

Choose your machine and tell us how to reach you.

Rise Tek will use these details to respond to your enquiry. Privacy policy