sales@risetekmachinery.com +1 905-487-3464 +1 (888) 827-0020 (toll-free)

sales@risetekmachinery.com

+1 905-487-3464

+1 (888) 827-0020 (toll-free)
Request Quote
Rise Tek Machinery > Fahditalia > Fahditalia Catalogue > Straightening Machines P180 KLASS

P180 KLASS

Planer shaft motor power (1st group)HP 5.5
Motor power spindle moulder right (2nd group)HP 5.5
Spindle spindle motor power left (3rd group)HP 5.5
Motor power upper horizontal shaft (4th group)HP 5.5
Feed motor powerHP 1 / 1.5
Max. working widthmm 180
Min working widthmm 25
Maximum working height (with tool diameter 125 mm)mm 105
Min working height (with tool diameter 125 mm)10 mm
Min workpiece length (single workpiece)mm 350
Shaft rotation speedrpm 6000
Diameter of drive rollers (toothed and rubberized)mm 120
Tool shaft diametermm 40
Horizontal tool lengthmm 190
Vertical tool lengthmm 120
Weightkg 950
CA MACHINE EQUIPMENT
  • Monobloc steel base suitably ribbed
  • Steel inlet surface with milled tubular structure 1700 mm long
  • Transmission by poly-V belts on all tool shafts, guarantee maximum engine power output
  • Independent motor unit on each workgroup
  • Upper crossbar equipped with motorized vertical movement, with drive rollers and pressers adjustable at the same time as the upper shaft for greater speed and ease of set-up
  • Forward system by means of cardan joints, single chain and 2-speed motor (7-14 m /1′)
  • Driving by means of 4 toothed rollers and 1 upper rubber roller at the exit
  • Air curtain on the work surface to facilitate the sliding of the workpiece
  • Left vertical shaft (3rd group) adjustable at the same time as the pressure group and output guide, for greater speed and ease of set-up
  • Pre-straightening system on the right side by means of skim cutter (on request) mounted on planer spindle
  • 0.1 mm precision decimal reading of 3rd – 4th shaft movements
  • Pneumatic pre-planer roller with control panel exclusion
  • Manual lubrication of the worktable
  • Direct motor start with illuminated pushbuttons from the control panel
  • Soundproof protection cabin complete with safety microswitch
  • Control panel with magnetothermal protection
  • Padlockable main switch
  • Nr. 2 emergency buttons
  • Low-voltage auxiliary circuit

ACCESSORIES ON REQUEST

Tool set: n. 02 heads 130 x 100 x 35; n. 02 heads 190 x 100 x 35; n. 01 skim coat cutter 12 x 120 x 35 (disposable knives); n. 01 gauge knife adjuster (if necessary)
Skim coat cutter (disposable knives) 12 x 120 x 35
Head 190 x 100 x 35 (horizontal shafts)
Head 130 x 100 x 35 (vertical shafts)
UL/CSA Regulatory
Difference Volts 220 and special voltages
Automatic lubrication of the work table
Automatic air and oil atomization
Additional drive shaft extension in front of the 3rd group, complete with 45 mm toothed roller
18 mm thick suppl.re toothed roller
45 mm thick suppl.re toothed roller
20 mm thick suppl.re rubber roller
50 mm thick suppl.re rubber roller
Pneumatic pressure on drive units
Automatic pre-planer override device when it enters the 1st drive roller
Variable speed drive with inverter kW 1.5
Pair of knife gauges
1st planer motor kW 5.5 (HP 7.5)
Kit for minimum working width 15 mm with two 10 mm sprockets

Request a Quote

    Rise Tek Machinery — Footer